BLADEZ T8 PRO - PARTS User Manual download pdf (Page 4)

www.tridonic.com

Subject to change without notice.

Data sheet 11/14-FO009-9

FL ballasts

Electronic ﬁxed output

RFI

Tridonic ballasts are RFI protected in accordance with EN 55015. To operate the

luminaire correctly and to minimise RFI we recommend the following instruc-

tions:

• Connection to the lamps of the “hot leads” must be kept as short as possible

(marked with *)

• Mains leads should be kept apart from lamp leads (ideally 5–10 cm distance)

• Do not run mains leads adjacent to the electronic ballast

• Twist the lamp leads

• Keep the distance of lamp leads from the metal work as large as possible

• Ballast must be earthed, either over the terminal or over the mounting screw

of the ballast

• Mains wiring to be twisted when through wiring

• Keep the mains leads inside the luminaire as short as possible

Defective lamp

If a lamp is defective, the ballast switches off and goes into standby. There is an

automatic restart once the lamp has been changed.

Loosen wire through

twisting and pulling

Side fixing feature

Screw M4, screw head diameter 8–10 mm

8 – 9 mm

wire preparation:

0.5 – 0.75 mm²

IDC interface

• solid wire with a cross section of 0.5 mm² according to the specification

from WAGO

Horizontal interface

• solid wire with a cross section of 0.5–0.75 mm² according to the specification

from WAGO

• solid wire with a cross section of 1.0 mm² with an insulation diameter up to

2.5 mm

• strip 9 mm of insulation from the cables to ensure perfect operation of the

push terminals

• Loosen wire through twisting and pulling

T8 lamp information

wattage

590 mm

1200 mm

1500 mm

18 W

36 W

58 W

length

Installation instructions

Isolation and electric strength testing of luminaires

Electronic devices can be damaged by high voltage. This has to be considered

during the routine testing of the luminaires in production.

According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A, each

luminaire should be submitted to an isolation test with 500 V

DC for 1 second. This

test voltage should be connected between the interconnected phase and neutral

terminals and the earth terminal.

The isolation resistance must be at least 2 MΩ.

As an alternative, IEC 60598-1 Annex Q describes a test of the electrical strength

with 1500 V

AC (or 1.414 x 1500 V DC). To avoid damage to the electronic devices this

test must not be conducted.

Additional information

Additional technical information at www.tridonic.com → Technical Data

Guarantee conditions at www.tridonic.com → Services

No warranty if device was opened.

Ballast Terminal Maximum capacitance allowed

Type Cold Hot Cold Hot

PC 1x... T8 PRO lp 13, 14 15, 16 200 pF 100 pF

PC 2x... T8 PRO lp/sl 11, 12, 13, 14 15, 16 200 pF 100 pF

PC 3/4x18 T8 PRO lp (3x18W) 9, 10, 11, 12, 13, 14 15, 16 200 pF 100 pF

PC 3/4x18 T8 PRO lp (4x18W) 6, 7, 9, 10, 11, 12, 13, 14 15, 16 200 pF 100 pF

Wiring advice

The lead length is dependant on the capacitance of the cable.

For safety reasons, the PC T8 PRO must only be earthed in the case of a safety class 1 luminaire.

Earthing is not required for the device to operate. Connection to earth reduces radio interference.

With standard solid wire 0.5/0.75 mm² the capa-

citance of the lead is 30–80 pF/m. This value is

influenced by the way the wiring is made.

• keep lamp wires short

• lamp connection with multi-lamp ballasts should

be made with symmetrical wiring

• lamp leads marked with * should be separated as

much as possible from other lamp leads

To avoid the damage of the control gear, the wiring must be protected against short circuits to earth

(sharp edged metal parts, metal cable clips, louver, etc.)

TC-L lamp information

wattage length

55 W 535 mm

1 2 3 4 5

Comments to this Manuals

No comments

BLADEZ T8 PRO - PARTS User Manual Page 4

Comments to this Manuals

Related products and manuals for Treadmills BLADEZ T8 PRO - PARTS